When you are done with your marble effect, click Apply. It will cause the area to blur and lose definition. While you are distorting the image, be careful not to extend the anchor points too far. We added a few more points and used those to pull out the edges. As more points are added, the more the design is distorted. You can add as many anchor points as you want. Don't worry about the white areas that show as we will fix this later. In the image below, the direction of the red arrows is where the points were dragged. Do the same with the other two anchor points. Once the anchor points have been placed click + drag one in any direction. Master is left at 100% and Linear Constraints left on Rigid. We placed three anchor points, one top left, a middle point and one bottom right. Every time you click, a new anchor point will be placed. This is because we need to place at least two anchor points.Ĭlick anywhere on the canvas and a circular anchor will be placed. If you try to adjust anything under the Deform panel, nothing will happen. Once again click on Filters, select Distort and then Deform. Step 2 - Add anchor points for the Deform Toolįor the next set of distortion we will use the Deform tool. At the top click on Filters, go to Distort then select Twirl. The Angle was set to 225.4° and the Radius set to 1024 px. Twirl distortion will create the first 'flow' of the design and help us get started quicker. When you add the distortion, Affinity Photo will change the layer from a grouped layer to a single Pixel layer. First, we will add a Twirl distortion to the design. With everything setup, now we can distort the design we have created. Once done, draw a selection box around all of the panels. Keep duplicating until your canvas is full. This will move the duplicates to the top of the Layers panel. Remember to click Move to Front each time you make duplicates. Next, press Ctrl + J to duplicate and Affinity Photo will shift them to the right. If not, go the Layers panel and Shift + click on the four layers at the top. The duplicate rectangles should still be selected. When you press Ctrl + J again, Affinity will remember and move the duplicates for you. This is because you are creating a new action. You will notice that when pressing Ctrl + J, Affinity Photo didn't adjust for you as before. While still selected click on Move to Front at the top of the screen. Now, click + drag the duplicates to the right until they snap into place. Press Ctrl + J to duplicate all four panels. Click on the Move tool top left and click + drag a selection box around the four panels. To quickly fill our canvas, we want to duplicate the four panels that we created. You will now have four panels, each with a different color. Remember to give the rectangle another color fill. Repeat for the last rectangle. Select the top most rectangle layer then press Ctrl + J. Affinity Photo will automatically move the rectangle into place for you. We will need to create another two duplicates, change the color and shift them. With the Snapping guide in place, a green and red line will show when it's aligned correctly. Change the color fill then click + drag it to the left until it covers half of the first rectangle. Go to the Layers panel and right click the rectangle layer then select Duplicate. Affinity Photo will create a new layer for the rectangleįill the rectangle with a color of your choice from the Color Panel on the right hand side. Now, draw out your rectangle as shown in the image below. It will show the last shape used filled in blue with a white triangle next to it.Ĭlick on the white triangle and select the Rectangle tool from the options. Then, on the left hand side panel, click on the shape tool. To keep everything aligned nicely, click on the Snapping tool at the top. But if the distortion works well enough, this layer won't be needed. This layer serves to fill any white gaps that you may have trouble covering. We will keep this for a background fill if needed later. Under the Layer panel on the right, click on Add Pixel Layer. For this tutorial, we filled four panels with blue, purple and black. Color choice is completely up to you including how many and the placement. We will be using the Rectangle tool to create panels and fill them with color. The base design needs to be set up before we can begin distorting it. Set up the base design to create the marble effect Once you have adjusted your settings, click Create. In this tutorial we are going to create a marble background in Affinity Photo. To start off, open Affinity Photo and select New Document. In Affinity Photo marble effects can be created using the distortion tools. Colors can be bold and striking or have a light pastel feel. The effect is great for use in wallpaper, paper crafts and even design fills. A marbled effect can give texture to backgrounds and create eye-catching designs.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |